Dynamic Load Cell

DLC101 : Dynamic Load Cell
Kliknìte zde pro vìtší obrázek.
  For High Frequency Tension/Compression Force Measurements
  Ideal for Measuring Impact or Pulsating Forces
  Frequency Range up to 25 kHz
  Force Ranges up to 5000 lb
  Calibration Certificate Supplied
  Stainless Steel Impact Cap and Mounting Stud Provided

OMEGA's DLC101 dynamic load cell is ideal for measuring force transients or dynamic force pulsations in impact or vibration applications. This load cell contains a thin piezoelectric crystal that generates an analog voltage signal in response to an applied dynamic force. The DLC101 has 2 threaded ends, enabling installation of threaded members such as mounting studs, impact caps, and machine elements. Its welded construction encloses and protects the crystals from the environment.

Excitation: 2 mA nominal @ 18 to 30 Vdc, constant current
Rated Output: 5V nominal FS
Amplitude Linearity: ±1% FS (BSFL/0)
Resonant Frequency (@ No Load): 75 kHz
High Frequency Range: 25 kHz (approx. 1/3 of resonant frequency, no load)
Low Frequency Range (-3 dB): 0.08 Hz
Stiffness: 11.4 lb/min
Overload Recovery: 10 ms for 2x range
Maximum Shock/Vibration: 10,000/±5000 g (no load)
Temperature Range: -75 to 120°C (-100 to 250°F)
Temperature Sensitivity Effect: 0.03% FSPF
Output Impedance: 100 Ω
Bias Voltage: 10V nominal
Weight: 43 g (1.5 oz) nominal
Material: 17-4 PH SS housing (RC 44)
Diameter of Top Force-Sensitive Surface: 13 mm (0.50")
Mounting Holes: ¼-28 x 0.175" deep tapped hole
Connector: Internal side coaxial, 10-32 male termination; cable sold separately; order ACC-CB2-10

Model No. Measurement
Range Comp.
Range Ten.
Time Constant
Noise Floor
(Wideband, RMS)
DLC101-10 0 to 10 0 to 10 50 s 200 lb 200 lb 0.00014 lb
DLC101-50 0 to 50 0 to 50 100 s 1000 lb 500 lb 0.0007 lb
DLC101-100 0 to 100 0 to 100 500 s 2000 lb 500 lb 0.0014 lb
DLC101-500 0 to 500 0 to 500 2000 s 10,000 lb 500 lb 0.007 lb
DLC101-1K 0 to 1000 0 to 500 2000 s 15,000 lb 500 lb 0.014 lb
DLC101-5K 0 to 5000 0 to 500 2000 s 15,000 lb 500 lb 0.07 lb

 Èíslo modelu  Cena (bez DPH)  Popis  Ks
 DLC101-10   Kontaktujte prodejce  Dynamic load cell with 10 lb range
 DLC101-50   Kontaktujte prodejce  Dynamic load cell with 50 lb range
 DLC101-100    13,550.00 Kč   Dynamic load cell with 100 lb range
 DLC101-500   Kontaktujte prodejce  Dynamic load cell with 500 lb range
 DLC101-1K   Kontaktujte prodejce  Dynamic load cell with 1000 lb range
 DLC101-5K    13,550.00 Kč   Dynamic load cell with 5000 lb range
 ACC-CB2-10    6,430.00 Kč   10 foot cable required to connect load cell to power supply
 ACC-PS1   Kontaktujte prodejce  9 volt battery power supply (BNCF connections)
 ACC-PS2    17,010.00 Kč   Recharge battery power supply (BNCF connections)
 ACC-PS3    16,860.00 Kč   115 Vac power supply (BNCF connections)
 ACC-CB4-15    2,080.00 Kč   15 ft coaxial cable (BNCM/BNCM)
 ACC-CB5-2    1,120.00 Kč   2 ft coaxial cable (BNCM/banana plugs)
 ACC-CB6    580.00 Kč   7 in coaxial cable (BNCM/pigtail)
Obsah košíku Vyprázdnit košík Objednat
 * využijte možnost konzultovat ceny pøímo s našimi prodejci  (tel: 596 311 899 - prodejní oddìlení, e-mail: viz. kontaktní informace)
 Poznámka: A complete system is a dynamic load cell, a power supply, and two cables; one between the load cell and the power supply and one from the power supply to your data system.

 Pøíklad objednávky: (1) ACC-CB2-10 10 foot coaxial cable (10-32/BNCM connections), (1) ACC-CB5-2 2 ft BNC to banana jack cable, ,  = 7,550.00 Kč

   Stáhnout kompletní specifikace produktu ve formátu PDF
   Stáhnout  DLC101 - Force Sensor
 Souvísející odkazy
   ACC-CABLES: Input/output Cables for Dynamic Sensors, Power Supplies and Instrumentation
   ACC-PS1 and ACC-PS2: Accelerometer Power Supplies, Battery Powered
   ACC-PS3 and ACC-PS4: Accelerometer Power Supplies, AC Powered, Single Channel and Triaxial Supply