DRSL-TEMP
Isolated DIN Rail Loop-Powered Temperature Signal Conditioner

DRSL-TEMP : Isolated DIN Rail Loop-Powered Temperature Signal Conditioner
Kliknìte zde pro vìtší obrázek.

3,510.00  Kč *
     DRSL-TEMP

  Type J or K Thermocouple or 2, 3 or 4-Wire Pt100 RTD Input
  Powered By the Host (Output) Current Signal Loop
  Slimline 6 mm (0.24") Housing
  High Accuracy
  Excellent EMC Performance and 50/60 Hz Noise Suppression
  Fast Response Time <30 ms/300 ms (Selectable)
  Pre-Calibrated Temperature Ranges Selectable via DIP-Switches

The DRSL-TEMP isolated DIN rail loop-powered temperature signal conditioner measures a standard type J or K thermocouple or a 2-, 3- or 4-wire Pt100 RTD temperature sensor and provides a passive analog current output signal.

The DRSL-TEMP offers 2-way isolation between input and output, provides surge suppression and protects control systems from transients and noise.

The DRSL-TEMP provides a competitive choice in terms of both price and technology for interfacing thermocouple or RTD signals to SCADA systems or PLC equipment. This unit is powered by the host (output) current signal loop. Low power consumption facilitates DIN rail mounting without the need for any air gap. Easy configuration of more than 1000 factory calibrated measurement ranges is done via DIP-switches. The unit operates over a wide temperature range from -25 to 70°C (-13 to 158°F).

SPECIFICATIONS
INPUT
THERMOCOUPLE INPUT
Type: J or K thermocouple
Temperature Range (DIP Swich Selectable)
    Type J: -100 to 1200°C (-148 to 2192°F)
    Type K: -180 to 1372°C (-292 to 2501°F)
Sensor and Cable Specifications: 5 kΩ per wire
Cold Junction Compensation (CJC): Internal or external (selectable)
    CJC Accuracy via External CJC (Pt100 RTD Sensor): Better than ±0.15°C
    CJC via Internally Mounted Sensor: Better than ±2.5°C
Open Thermocouple Detection: Yes (DIP switch selectable upscale or downscale)
Pt100 RTD INPUT
Type: 2, 3, or 4-wire Pt100 RTD
Temperature Range (DIP Switch Selectable): -200 to 850°C (-328 to 1562°F)
Sensor Current, RTD: <150 µA
Sensor Cable Specifications: 50 Ω per wire
Effect of Sensor Cable Resistance (3 or 4-Wire RTD): <0.002 Ω/Ω
Broken Sensor Detection: >800 Ω
Shorted Sensor Detection: <18 Ω

OUTPUT
Current Output
    Programmable Signal Ranges: 0 to 20 mA and 4 to 20 mA
    Range Limits (NAMUR NE43 Out of Range): Below 3.8 mA or above 20.5 mA
    Sensor Error Detection (Dip Switch Selectable for Enable or None): Below 3.5 mA or above 23 mA
    Incorrect DIP-Switch Setting Identification: Below 3.5 mA
    Output Error Level: DIP switch selectable for upscale or downscale
    Load Resistance (Ω): ≤(Vsupply - 5.5)/0.023
    Load Stability: ≤0.01% of span/100 Ω

GENERAL
Supply Voltage: 5.5 to 35 Vdc
Voltage Drop: 5.5 Vdc
Isolation: Input/output
Isolation Voltage (Test): 2.5 kVac (reinforced)
Isolation Voltage (Working): 300 Vac
Signal/Noise Ratio: >60 dB
Response Time (0 to 90%, 100 to 10%): <30 ms/300 ms (selectable, provides either fast response or signal dampening as needed)
Accuracy
    Thermocouple Input: Better than 0.5°C or ±0.05% of span (selected input range)
    RTD Input: Better than 0.1°C or ±0.05% of span (selected input range)
Temperature Coefficient
    Thermocouple Input: ≤±0.1°C/°C or ≤±0.01%/°C
    RTD Input: ≤±0.02 °C/°C
EMC Immunity Influence: <±0.5% of span
Extended EMC Immunity
    NAMUR NE 21, A Criterion, Burst: <±1% of span (span = selected input range)

ENVIRONMENTAL
Operating Temperature: -25 to 70°C (-13 to 158°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Calibration Temperature: 20 to 28°C (68 to 82°F)
Relative Humidity: 0 to 95% RH non-condensing
Protection Degree: IP20
Installation Area: Pollution degree 2 and measurement/overvoltage category II

MECHANICAL
Dimensions: 113 H x 6.1 W x 115 mm D (4.4 x 0.24 x 4.5")
Weight: 70 g (0.15 lb) approx
DIN Rail Type: DIN EN 60715 - 35 mm
Wire Size: 0.13 x 2.5 mm²/AWG 26 to 12 stranded wire
Screw Terminal Torque: 0.5 Nm


 Èíslo modelu  Cena (bez DPH)  Popis  Ks
 DRSL-TEMP    3,510.00 Kč   Isolated DIN rail loop-powered temperature signal conditioner
 RAIL-35-1    300.00 Kč   35 mm (1.4") DIN rail, 1 m (3.3') length
 DRSL-MOD-STOP    140.00 Kč   Module stop (screwed onto DIN rail to support and hold mounted devices)
Obsah košíku Vyprázdnit košík Objednat
 * využijte možnost konzultovat ceny pøímo s našimi prodejci  (tel: 596 311 899 - prodejní oddìlení, e-mail: viz. kontaktní informace)
 Pøíklad objednávky: (1) DRSL-MOD-STOP Module stop (screwed onto DIN rail to support and hold mounted devices), (1) DRSL-TEMP Isolated DIN rail loop-powered temperature signal conditioner, (1) RAIL-35-1 35 mm (1.4 = 3,950.00 Kč

 Literatura
   Stáhnout kompletní specifikace produktu ve formátu PDF
 Manuály
   Stáhnout  Installation Guide for Signal Conditioners
 Souvísející odkazy
   DRSL-DC1: Isolated DIN Rail Repeater
   DRSL-DC2: Isolated DIN Rail Signal Conditioner
   DRSL-DC3: Isolated DIN Rail Signal Conditioner
   DRSL-DC4: Bipolar Isolated DIN Rail Signal Conditioner for Process Signals
   DRSL-LPI_Series: DIN Rail Input Loop-Powered Isolators
   DRSL-LPO_Series: DIN Rail 2-Wire Transmitter Isolators
   DRSL-RTD-LP: RTD Input Non-Isolated DIN Rail Loop-Powered Signal Conditioner
   DRSL-RTD_Series: RTD Input DIN Rail Signal Conditioners
   DRSL-SP1: Isolated DIN Rail Repeater/Splitter for Current Signals
   DRSL-SP2: Isolated DIN Rail Signal Conditioner/Splitter for Process Signals
   DRSL-SP3: Bipolar Isolated DIN Rail Signal Conditioner/Splitter for Process Signals
   DRSL-TC_Series: Thermocouple Input DIN Rail Signal Conditioners
   DRSL-U: Isolated Universal Input DIN Rail Signal Conditioner