PTFE Liquid Flow Sensors

FPR-1500 : PTFE Liquid Flow Sensors
Kliknìte zde pro vìtší obrázek.

31,030.00  Kč *

  Provides Highly Linear 0 to 5 Vdc Output Signal and Buffered Linear Pulse Output Signal for Totalizing
  Micro-Liquid Flow Rates as Low as 15 ml/min Can Be Measured with High Precision
  Usable with a Variety of Low Viscosity Liquids Including Many Corrosive Liquid Chemicals

FPR1501 Series flow sensors can measure extremely low flow rates from 15 mL/min. They are suitable for a wide variety of industrial, commercial, and laboratory flow applications.

Because the FPR1501 flow sensors have only PTFE and sapphire wetted surfaces, it is anticipated that they will replace conventional glass tube and ball flowmeters in many applications in which an electrical signal proportional to flow rate is desirable, even in very corrosive applications in which the liquid is low in viscosity (i.e., less than 10 centistokes).

Models use a Pelton-type turbine wheel to determine the flow rate of the liquid. The rotation rate of the turbine wheel is linear over a large dynamic range. The electro-optical system consists of a diode emitting energy in the infrared spectrum. Light energy is interrupted and passed from 8 small holes in the small turbine wheel. This reflected light energy is detected by a photodiode. Thus, as the turbine wheel rotates in response to the liquid flow rate, electrical pulses are generated. Processing circuitry provides a DC voltage output and buffered square-wave output pulses that are proportional to the flow rate.

Tube Fitting:
1/8" tube fittings for flowrates up to 100 ml/min
¼" tube fitting for flow rates from 100 ml/min. to 2 liters/min
3/8" tube fitting for flow rates greater than 2 liters/min.

Output Signal: 0 to 5 Vdc, adjustable ±20% (typical) and pulse output from 0 to 300/500 pps (typical) @ 7.5 Vdc peak pulse height-linear
Power Requirements: 12 to 15 Vdc regulated, 50 mA
Standard Sensor Material: PTFE, sapphire, Perfluoroelastomer gasket; PFA compression tube fittings
Pressure Rating: 4 bar (60 psig) max
Temperature Rating: 0 to 70°C (32 to 158°F)
Temperature Sensitivity: ±0.2%/°C
Accuracy: ±3% FS
Repeatability: ±0.2% FS from 20 to 100% of rated max flow
Dimensions: 55.6 x 48.0 x 58.9 mm (2.19 x 1.89 x 2.32") not including fittings
Applicable Liquids: Many low-viscosity (<10 centistokes) liquids; check compatibility with wetted materials; specify liquid when ordering

 Èíslo modelu  Cena (bez DPH)  Popis  Ks
 FPR1501    31,030.00 Kč   15 to 100 ml/min, 1/8" tube fitting
 FPR1502    31,030.00 Kč   25 to 200 ml/min, 1/4" tube fitting
 FPR1503    31,030.00 Kč   50 to 500 ml/min, 1/4" tube fitting
 FPR1504    31,030.00 Kč   100 to 1000 ml/min, 1/4" tube fitting
 FPR1505    31,030.00 Kč   0.2 to 2.0 l/min, 1/4" tube fitting
 FPR1506    34,340.00 Kč   0.5 to 5.0 l/min, 3/8" tube fitting
 FPR1500-PW    2,840.00 Kč   Power supply, 115 Vac to 12 Vdc
 FPR1500-230PW    2,840.00 Kč   Power supply, 230 Vac to 12 Vdc, with European plug
 DP25B-E    8,820.00 Kč   Analog input panel meter with 12 volt excitation
Obsah košíku Vyprázdnit košík Objednat
 * využijte možnost konzultovat ceny pøímo s našimi prodejci  (tel: 596 311 899 - prodejní oddìlení, e-mail: viz. kontaktní informace)
 Poznámka: Comes complete with 0.9 m (3') long cable with pigtails and operator's manual.

Note: Maximum differential pressure (delta P) across flow sensor occurs at maximum rated flow using water at 23°C (73°F). At 50% of rated flow,delta P is 0.25 of value at max. rated flow, and, at 20% of rated flow, delta P is 0.04 of value at max. rated flow.

 Pøíklad objednávky: (1) DP25B-E 1/8 DIN Panel meter with 12 volt excitation, (1) FPR1506 flow sensor with 0.5 to 5.0 l/min range = 43,160.00 Kč

   Stáhnout kompletní specifikace produktu ve formátu PDF
   Stáhnout  FPR1500 Series - PTFE Liquid Flow Sensor
 Souvísející odkazy
   DP25B Series: 1/8 DIN Process Meter & Controller
   CL535: Frequency Calibrator with Totalizer