FPU2000, FPUVS2000, FPUDV2000
Variable Speed and Fixed Peristaltic Pumps

FPU2000, FPUVS2000, FPUDV2000 : Variable Speed and Fixed Peristaltic Pumps
Kliknìte zde pro vìtší obrázek.

33,150.00  Kč *

  Peristaltic Pump Tube Does Not Require Valves
  Self Priming
  High Outlet Pressure Capability of 100 psig on Most Models
  Acceptable for Indoor Use
  Corrosion Proof Valox Housing
  Tamper Resistant Electronic Control Panel Cover
  Tube Failure Detection

The FPU2000 series has been discontinued. Please see the FPU2000A Series as a possible alternative or contact our Flow Engineering department.

The FPU2000 Series fixed pumps feed by an analog fixed 60 second timer. The pump can be on for 1 to 60 seconds. All FPU2000 Series have fixed speed outputs and can be adjusted by selecting the pumphead tube size and choosing the desired RPM (revolutions per minute).

The FPUVS2000 and FPUDVS2000 Series variable speed pumps are for continuous pumping relatively pulse free, even while adjusting the percentage of output. The variable speed pump requires the use of brushes on the DC motor. Excellent brush life expectancy (2000 hours). An extra set of brushes included with every pump.

The FPUDVS2000 Series will accept any one of three different types of external input signals; 4 to 20 mA, 0 to 10 Vdc, or frequency. The 4 to 20 mA and 0 to 10 Vdc loops must be powered. Two types of frequency inputs, AC sine waves (magnetic coils type outputs) and digital square waves (Hall Effect signals, contact closures), are acceptable. A jumper plug located on the circuit board is factory pre-set for AC sine wave signals, the jumper must be re-positioned when digital square wave signals are being used. All wiring connections are to be made inside of the junction box located on the side of the FPUDVS2000 Series.

A liquid tight connector is supplied and should be used for the external signal cable. The signal input wires are color coded to the type of signal being used.

Maximum Working Pressure: 100 psig/6.9 bar (most models)
Maximum Fluid Temperature: 54°C (130°F)
Ambient Temperature Range: -10 to 43°C (14 to 110°F)
Enclosure: NEMA 3R (IP24) (acceptable for indoor use)
Pump Tube Material: Norprene
Duty Cycle: Continuous
Maximum Solids: 50% by volume
Maximum Viscosity: 5000 Centipoise
Maximum Suction Lift: Up to 9 m (30') water
Turn Down Ratio: 20:1
Power Requirements: 115 V 60 Hz 80 Watts, 220 V 50 Hz 40 Watts, 230 V 60 Hz 45 Watts
Variable Speed: 115 V 60 Hz 40 Watts, 220 V 50 Hz 40 Watts, 230 V 60 Hz 40 Watts
Dimensions: 155.6 H x 257.2 W x 228.6 mm D (618 x 1018 x 9")
Variable Speed: 159 H x 254 W x 235 mm D (6¼ x 10 x 9¼")
Weight: 3.6 kg (8 lb)
Tube Connection: Compression barb type (38" ID x ¼" OD)

 Èíslo modelu  Cena (bez DPH)  Popis  Ks
 FPU2006    16,650.00 Kč   Max Feed Rate: 42 ml/min (16 GPD)
 FPU2010    16,650.00 Kč   Max Feed Rate: 138 ml/min (52.5 GPD)
 FPUVS2002    22,500.00 Kč   Max Feed Rate: 13 ml/min (4.9 GPD)
 FPUVS2005    22,950.00 Kč   Max Feed Rate: 28 ml/min (6.8 GPD)
 FPUDVS2005    33,450.00 Kč   Max Feed Rate: 28 ml/min (6.8 GPD)
 FPUDVS2007    33,150.00 Kč   Max Feed Rate: 63 ml/min (24 GPD)
 FPUDVS2008    33,150.00 Kč   Max Feed Rate: 79 ml/min (30.1 GPD)
 FPU1000-AB    920.00 Kč   Quantity 2, armature bearings
 FPU1000-IF    1,170.00 Kč   Injection fitting
 FPU2000-14PTA    890.00 Kč   1/4" OD pump tube assembly
 FPU2000-38PTA    1,010.00 Kč   3/8" OD pump tube assembly
 FPU2000-716PTA    1,040.00 Kč   7/16" OD pump tube assembly
 FPU2000-CW    100.00 Kč   Ceramic weight
 FPU2000-PH    1,950.00 Kč   Pump head
 FPU2000-PHB    740.00 Kč   Pump head cover with bearing
 FPU2000-RA    2,010.00 Kč   Roller assemblies for 1/4 and 3/8" tube models
 FPU2000-716RA    2,010.00 Kč   Roller assemblies for the 7/16" tube model
 FPU2000-SP    130.00 Kč   Strainer plug
 FPU2000-TN    130.00 Kč   Tube nut (3/8")
Obsah košíku Vyprázdnit košík Objednat
 * využijte možnost konzultovat ceny pøímo s našimi prodejci  (tel: 596 311 899 - prodejní oddìlení, e-mail: viz. kontaktní informace)
 Poznámka: Comes complete with suction tube strainer, tube weight, suction tubing, discharge tubing and injection fitting with internal back-flow check valve, mounting hardware, and operator’s manual.

FPUVS and FPUDVS come with an additional set of brushes.

For optional CE approved 220 Vac/50Hz add suffix "-220/50" to model number, no additional charge.

For optional CE approved 230 Vac/60 Hz model add suffix "-230/60" to model number, no additional charge.

Note: 220 Vac/50Hz fixed speed models output approximately 20% less.

 Pøíklad objednávky: (1) FPUDVS2007 Digital Peristaltic Pump = 33,150.00 Kč

(1) (2) (3)
FPU 20
Popis voleb
(1) Variable Speed
  Vyberte prázdné pole pro None, VS pro Standard Percentage, DVS pro Digital percentage controller
(2) Max Feed Rate
  Vyberte 01 pro 6 ml/min (2.3 GPD), 02 pro 13 ml/min (4.9 GPD), 03 pro 21 ml/min (8 GPD), 04 pro 25 ml/min (9.5 GPD), 05 pro 18 ml/min (6.8 GPD), 06 pro 42 ml/min (16 GPD), 07 pro 63 ml/min (24 GPD), 08 pro 79 ml/min (30.1 GPD), 09 pro 57 ml/min (21.7 GPD), 10 pro 138 ml/min (52.5 GPD), 11 pro 200 ml/min (76.1 GPD), 12 pro 250 ml/min (95.1 GPD)
(3) Additional Option
  Vyberte prázdné pole pro None, -220/50 pro 220 Vac/50Hz model, -230/60 pro 230 Vac/60 Hz model
 Poznámka: ne všechny kombinace jsou správné, ovìøte si správnost èísla modelu.

   Stáhnout kompletní specifikace produktu ve formátu PDF
   Stáhnout  FPUDVS2000 Series - Digital Variable Speed Peristaltic Injector Pump