SCR19 and SCR39 Series
SCR Power Controllers for Electrical Resistance Heaters

SCR19 and SCR39 Series : SCR Power Controllers for Electrical Resistance Heaters
Kliknėte zde pro vėtší obrázek.

9,180.00  Kč *
     SCR19Z-24-040

  Zero Crossing or Phase Angle Fired
  Single or Three Phase Load Switching
  Extends Heater Life Reduces Thermal Shock
  No Maintenance All Solid State Components
  Close Control of Low Mass Heaters
  Phase Angle with Soft Start for High Inrush Heaters
  No Relay Noise Contact Arc Noise Eliminated
  Semiconductor I2T Fusing
  Optically Isolated Control Signal Input

The SCR19 Series Power Controllers are designed to proportion electric power to resistive loads only, such as ovens, furnaces, heat sealers, etc. (NOTE: They are not designed to drive transformers or any inductive load.) The controllers consist of power semi-conductors (SCRs), properly-sized heat sinks, trigger circuitry, and fuses supplied on panels for surface mounting. The power controller accepts a 4 to 20 mA dc output from a temperature controller or can be supplied with manual option using a remote potentiometer.

The SCR19 Series controllers offers two methods of proportional control – Zero-voltage-switched and Phase-angled-fired. With the Zero-voltage-switching mode, the controller switches on complete cycles of the ac supply voltage. The trigger circuit is designed to turn on the SCRs as close as possible to the point where the AC sine wave crosses through zero. In effect, the line voltage is turned on and off and applied to the heaters in whole cycles. With an input of 4 to 20 mA, the output will be off below 4 mA and full on at 20 mA. Proportioning action is obtained by varying the number of cycles on to the number of cycles off. The output will vary from one cycle on and nine cycles off at low input, to all cycles on at maximum input. This output is integrated by the heaters which produce a smoothly proportioning heat output that varies directly with the input signal. With the Phase-angle-fired mode, the power to the load is controlled by governing the point of turn on (firing) of each half cycle of the full AC sine wave.


 Číslo modelu  Cena (bez DPH)  Popis  Ks
 SCR19Z-12-040    9,420.00 Kč   SCR, Zero-Voltage-Switching, 120V, 40A
 SCR19Z-24-040    9,180.00 Kč   SCR, Zero-Voltage-Switching, 240V, 40A
 SCR19Z-48-040    9,630.00 Kč   SCR, Zero-Voltage-Switching, 480V, 40A
 SCR19Z-24-060    9,480.00 Kč   SCR, Zero-Voltage-Switching, 240V, 60A
 SCR39Z-24-060    18,150.00 Kč   SCR, 3-phase, Zero-Voltage-Switching, 240V, 60A
 SCR39Z-48-060    19,350.00 Kč   SCR, 3-phase, Zero-Voltage-Switching, 480V, 60A
 SCR19P-24-040-S15    11,310.00 Kč   SCR, Phase-Angle-Switching, 240V, 40A, 15 sec soft start circuit
 SCR19P-24-080-S9    12,150.00 Kč   SCR, Phase-Angle-Switching, 240V, 80A, 9 sec soft start circuit
 SCR-210A015U01    2,010.00 Kč   Replacement Fuse, 40 A
 SCR-210A012U01    2,640.00 Kč   Replacement Fuse, 60 A
 SCR-210A014U01    2,460.00 Kč   Replacement Fuse, 80 A
 SCR19Z-M    3,060.00 Kč   Manual remote pot for 120V SCR19/39 models
 SCR19Z-M-220    3,060.00 Kč   Manual remote pot for 240V SCR19/39 models
 SCR19Z-M-480    3,060.00 Kč   Manual remote pot for 480V SCR19/39 models
Obsah košíku Vyprázdnit košík Objednat
 * využijte možnost konzultovat ceny pøímo s našimi prodejci  (tel: 596 311 899 - prodejní oddėlení, e-mail: viz. kontaktní informace)
 Poznámka: Comes with complete operator’s manual
 Pøíklad objednávky: (1) SCR19Z-24-040 SCR, Zero-Voltage-Switching, 240V, 40A = 9,180.00 Kč

(1) (2) (3) (4) (5)
SCR 9
Popis voleb
(1) Single or 3 Phase
  Vyberte 1 pro Single Phase, 3 pro 3 Phase
(2) Method
  Vyberte Z pro Zero-Voltage Switching, P pro Phase-Angle Firing
(3) Voltage
  Vyberte -02 pro 24 Vac for single phase only, -12 pro 120 Vac for single phase only, -20 pro 208 Vac for phase angle firing, -24 pro 240 Vac, -48 pro 480 Vac
(4) Current
  Vyberte -040 pro 40 Amps , -060 pro 60 Amps, -080 pro 80 Amps
(5) Phase-Angle Firing Items
  Vyberte pro Zero-Voltage Switching leave field blank, -S9 pro the STANDARD Soft start 9 seconds, -S15 pro Soft start 15 seconds, -S30 pro Soft start 30 seconds, -S60 pro Soft start 60 seconds, -S120 pro Soft start 120 seconds, -V pro Voltage limit
 Poznámka: ne všechny kombinace jsou správné, ovėøte si správnost čísla modelu.

 Literatura
   Stáhnout kompletní specifikace produktu ve formátu PDF
 Manuály
   Stáhnout  SCR19/39 - Power Controllers